Press "Enter" to skip to content

Free Share CertBus Cisco 400-101 Exam Dumps and Practice Questions and Answers

CertBus 2018 Newest Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

400-101 CCIE Exam PDF and VCE Dumps : 1436QAs Instant Download: https://www.certbus.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certbus.com/online-pdf/400-101.pdf
☆ CertBus 2018 Newest 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1436QAs are all new published by Cisco Official Exam Center

One of my colleague recommend me that CertBus CCIE Latest 400-101 vce dumps are effective and helpful. Thank goodness I followed up with him and choose CertBus as my assistance on my CCIE Nov 07,2018 Latest 400-101 vce CCIE Routing and Switching Written v5.0 certification exam! I passed my Cisco CCIE Latest 400-101 QAs exam very easily. I was lucky, all my questions in the exams were from my Cisco CCIE Latest 400-101 free download dumps.

unlimited access to 3500 CertBus exams q and a. CertBus- hottest 400-101 certification practice questions and answers. help candidates get well prepared for their 400-101 certification exams. CertBus | lead to pass 400-101 certification exams. first test, first pass! CertBus – your reliable partner and professional 400-101 certification exam material provider.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certbus.com/400-101.html

QUESTION NO:3

A new backup connection is being deployed on a remote site router. The stability of the connection

has been a concern. In order to provide more information to EIGRP regarding this interface, you

wish to incorporate the “reliability” cost metric in the EIGRP calculation with the command metric

weights 1 0 1 0 1.

What impact will this modification on the remote site router have for other existing EIGRP

neighborships from the same EIGRP domain?

A. Existing neighbors will immediately begin using the new metric.

B. Existing neighbors will use the new metric after clearing the EIGRP neighbors.

C. Existing neighbors will resync, maintaining the neighbor relationship.

D. All existing neighbor relationships will go down.

Answer: D

Explanation:


QUESTION NO:5

Refer to the exhibit.

A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used

for the default route, pointing to both interfaces with a different administrative distance, so that one

of the default routes is preferred.

Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.

After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static

route remained active. They lost their Internet connectivity, even though the backup link was

operating.

Which two possible solutions can be implemented to avoid this situation in the future? (Choose

two.)

A. Implement HSRP link tracking on the branch router R1.

B. Use a track object with an IP SLA probe for the static route on R1.

C. Track the link state of the Ethernet link using a track object on R1.

D. Use a routing protocol between R1 and the upstream ISP.

Answer: B,D

Explanation:

Interface Tracking

Interface tracking allows you to specify another interface on the router for the HSRP process to

monitor in order to alter the HSRP priority for a given group.

If the specified interface\’s line protocol goes down, the HSRP priority of this router is reduced,

allowing another HSRP router with higher priority can become active (if it has preemption

enabled).

To configure HSRP interface tracking, use the standby [group] track interface [priority] command.

When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you

explicitly set the decrement value, then the value is decreased by that amount if that interface is

down, and decrements are cumulative. If you do not set an explicit decrement value, then the

value is decreased by 10 for each interface that goes down, and decrements are cumulative.

The following example uses the following configuration, with the default decrement value of 10.

Note: When an HSRP group number is not specified, the default group number is group 0.

interface ethernet0

ip address 10.1.1.1 255.255.255.0

standby ip 10.1.1.3

standby priority 110

standby track serial0

standby track serial1

The HSRP behavior with this configuration is:

0 interfaces down = no decrease (priority is 110)

1 interface down = decrease by 10 (priority becomes100)

2 interfaces down = decrease by 10 (priority becomes 90)

Reference

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i

ntracking


QUESTION NO:7

Which statement is true about TCN propagation?

A. The originator of the TCN immediately floods this information through the network.

B. The TCN propagation is a two step process.

C. A TCN is generated and sent to the root bridge.

D. The root bridge must flood this information throughout the network.

Answer: C

Explanation:

Explanation

New Topology Change Mechanisms

When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the

root bridge.

This is shown in this diagram:

Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the

BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge

receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay

seconds. This ensures a relatively quick flush of stale information. Refer to Understanding

Spanning-Tree Protocol Topology Changes for more information on this process. This topology

change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its

propagation through the network evolve.

Topology Change Detection

In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This

means that a loss of connectivity is not considered as a topology change any more, contrary to

802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge

detects a topology change, these occur:

It starts the TC While timer with a value equal to twice the hello-time for all its non-edge

designated ports and its root port, if necessary.

It flushes the MAC addresses associated with all these ports.

Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC

bit set.

BPDUs are also sent on the root port while the timer is active.

Topology Change Propagation

When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:

It clears the MAC addresses learned on all its ports, except the one that receives the topology

change.

It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port

(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).

This way, the TCN floods very quickly across the whole network. The TC propagation is now a one

step process. In fact, the initiator of the topology change floods this information throughout the

network, as opposed to 802.1D where only the root did. This mechanism is much faster than the

802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the

topology change state for the whole network for seconds.

In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of

the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but

on the other hand it clears potential stale information that prevents rapid connectivity restitution.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml


QUESTION NO:8

Which statement is true about loop guard?

A. Loop guard only operates on interfaces that are considered point-to-point by the spanning tree.

B. Loop guard only operates on root ports.

C. Loop guard only operates on designated ports.

D. Loop guard only operates on edge ports.

Answer: A

Explanation:

Explanation

Understanding How Loop Guard Works

Unidirectional link failures may cause a root port or alternate port to become designated as root if

BPDUs are absent. Some software failures may introduce temporary loops in the network. Loop

guard checks if a root port or an alternate root port receives BPDUs. If the port is receiving

BPDUs, loop guard puts the port into an inconsistent state until it starts receiving BPDUs again.

Loop guard isolates the failure and lets spanning tree converge to a stable topology without the

failed link or bridge.

You can enable loop guard per port with the set spantree guard loop command.

Note When you are in MST mode, you can set all the ports on a switch with the set spantree

global-defaults loop-guard command.

When you enable loop guard, it is automatically applied to all of the active instances or VLANs to

which that port belongs. When you disable loop guard, it is disabled for the specified ports.

Disabling loop guard moves all loop-inconsistent ports to the listening state.

If you enable loop guard on a channel and the first link becomes unidirectional, loop guard blocks

the entire channel until the affected port is removed from the channel. Figure 8-6 shows loop

guard in a triangle switch configuration.

Figure 8-6 Triangle Switch Configuration with Loop Guard

Figure 8-6 illustrates the following configuration:

Switches A and B are distribution switches.

Switch C is an access switch.

Loop guard is enabled on ports 3/1 and 3/2 on Switches A, B, and C.

Use loop guard only in topologies where there are blocked ports. Topologies that have no blocked

ports, which are loop free, do not need to enable this feature. Enabling loop guard on a root switch

has no effect but provides protection when a root switch becomes a nonroot switch.

Follow these guidelines when using loop guard:

Do not enable loop guard on PortFast-enabled or dynamic VLAN ports.

Do not enable PortFast on loop guard-enabled ports.

Do not enable loop guard if root guard is enabled.

Do not enable loop guard on ports that are connected to a shared link.

Note: We recommend that you enable loop guard on root ports and alternate root ports on access

switches.

Loop guard interacts with other features as follows:

Loop guard does not affect the functionality of UplinkFast or BackboneFast.

Root guard forces a port to always be designated as the root port. Loop guard is effective only if

the port is a root port or an alternate port. Do not enable loop guard and root guard on a port at the

same time.

PortFast transitions a port into a forwarding state immediately when a link is established. Because

a PortFast-enabled port will not be a root port or alternate port, loop guard and PortFast cannot be

configured on the same port. Assigning dynamic VLAN membership for the port requires that the

port is PortFast enabled. Do not configure a loop guard-enabled port with dynamic VLAN

membership.

If your network has a type-inconsistent port or a PVID-inconsistent port, all BPDUs are dropped

until the misconfiguration is corrected. The port transitions out of the inconsistent state after the

message age expires. Loop guard ignores the message age expiration on type-inconsistent ports

and PVID-inconsistent ports. If the port is already blocked by loop guard, misconfigured BPDUs

that are received on the port make loop guard recover, but the port is moved into the type-

inconsistent state or PVID-inconsistent state.

In high-availability switch configurations, if a port is put into the blocked state by loop guard, it

remains blocked even after a switchover to the redundant supervisor engine. The newly activated

supervisor engine recovers the port only after receiving a BPDU on that port.

Loop guard uses the ports known to spanning tree. Loop guard can take advantage of logical ports

provided by the Port Aggregation Protocol (PAgP). However, to form a channel, all the physical

ports grouped in the channel must have compatible configurations. PAgP enforces uniform

configurations of root guard or loop guard on all the physical ports to form a channel.

These caveats apply to loop guard:


QUESTION NO:16

In 802.1s, how is the VLAN to instance mapping represented in the BPDU?

A. The VLAN to instance mapping is a normal 16-byte field in the MST BPDU.

B. The VLAN to instance mapping is a normal 12-byte field in the MST BPDU.

C. The VLAN to instance mapping is a 16-byte MD5 signature field in the MST BPDU.

D. The VLAN to instance mapping is a 12-byte MD5 signature field in the MST BPDU.

Answer: C

Explanation:

MST Configuration and MST Region

Each switch running MST in the network has a single MST configuration that consists of these

three attributes:

1. An alphanumeric configuration name (32 bytes)

2. A configuration revision number (two bytes)

3. A 4096-element table that associates each of the potential 4096 VLANs supported on the

chassis to a given instance.

In order to be part of a common MST region, a group of switches must share the same

configuration attributes.

It is up to the network administrator to properly propagate the configuration throughout the region.

Currently, this step is only possible by the means of the command line interface (CLI) or through

Simple Network

Management Protocol (SNMP). Other methods can be envisioned, as the IEEE specification does

not explicitly mention how to accomplish that step.

Note: If for any reason two switches differ on one or more configuration attribute, the switches are

part of different regions. For more information refer to the Region Boundary section of this

document.

Region Boundary

In order to ensure consistent VLAN-to-instance mapping, it is necessary for the protocol to be able

to exactly identify the boundaries of the regions. For that purpose, the characteristics of the region

are included in the BPDUs. The exact VLANs-to-instance mapping is not propagated in the BPDU,

because the switches only need to know whether they are in the same region as a neighbor.

Therefore, only a digest of the VLANs-toinstance mapping table is sent, along with the revision

number and the name. Once a switch receives a BPDU, the switch extracts the digest (a

numerical value derived from the VLAN-to-instance mapping table through a mathematical

function) and compares this digest with its own computed digest. If the digests differ, the port on

which the BPDU was received is at the boundary of a region.

In generic terms, a port is at the boundary of a region if the designated bridge on its segment is in

a different region or if it receives legacy 802.1d BPDUs. In this diagram, the port on B1 is at the

boundary of region A, whereas the ports on B2 and B3 are internal to region B:

MST Instances

According to the IEEE 802.1s specification, an MST bridge must be able to handle at least these

two instances:

One Internal Spanning Tree (IST)

One or more Multiple Spanning Tree Instance(s) (MSTIs)

The terminology continues to evolve, as 802.1s is actually in a pre-standard phase. It is likely

these names will change in the final release of 802.1s. The Cisco implementation supports 16

instances: one IST (instance 0) and 15 MSTIs.

show vtp status

Cisco switches “show vtp status” Field Descriptions has a MD5 digest field that is a 16-byte

checksum of the

VTP configuration as shown below

Router# show vtp status

VTP Version: 3 (capable)

Configuration Revision: 1

Maximum VLANs supported locally: 1005

Number of existing VLANs: 37

VTP Operating Mode: Server

VTP Domain Name: [smartports]

VTP Pruning Mode: Disabled

VTP V2 Mode: Enabled

VTP Traps Generation: Disabled

MD5 digest : 0x26 0xEE 0x0D 0x84 0x73 0x0E 0x1B 0x69

Configuration last modified by 172.20.52.19 at 7-25-08 14:33:43

Local updater ID is 172.20.52.19 on interface Gi5/2 (first layer3 interface fou)

VTP version running: 2

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfc.shtml

http://www.cisco.com/en/US/docs/ios-xml/ios/lanswitch/command/lsw-cr-book.pdf


400-101 PDF Dumps400-101 Study Guide400-101 Exam Questions

QUESTION NO:17

Which three combinations are valid LACP configurations that will set up a channel? (Choose

three.)

A. On/On

B. On/Auto

C. Passive/Active

D. Desirable/Auto

E. Active/Active

F. Desirable/Desirable

Answer: A,C,E

Explanation:


QUESTION NO:20

Refer to the exhibit.

What is the potential issue with this configuration?

A. There is no potential issue; OSPF will work fine in any condition.

B. Sub-optimal routing may occur since there is no area 1 adjacency between the ABRs.

C. This is a wrong OSPF configuration because all routers must be in area 0 only.

D. This is a wrong OSPF configuration because /30 requires 0.0.0.3 wild card.

Answer: B

Explanation:


QUESTION NO:23

What action will a BGP route reflector take when it receives a prefix marked with the community

attribute NO ADVERTISE from a client peer?

A. It will advertise the prefix to all other client peers and non-client peers.

B. It will not advertise the prefix to EBGP peers.

C. It will only advertise the prefix to all other IBGP peers.

D. It will not advertise the prefix to any peers.

Answer: D

Explanation:


QUESTION NO:24

Refer to the exhibit.

R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).

What can be done so that R1 will learn about this network?

A. Disable auto-summary on R2.

B. Configure an explicit network command for the 172.16.10.0 subnet on R2.

C. Subnet information cannot be passed between IBGP peers.

D. Disable auto-summary on R1.

Answer: B

Explanation:

By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet

routes in BGP, use an explicit network command or the no auto-summary command. If you disable

auto-summarization and have not entered a network command, you will not advertise network

routes for networks with subnet routes unless they contain a summary route.

Reference

http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html


QUESTION NO:26

Refer to the exhibit.

Why is AS 65333 in parentheses?

A. It is an external AS.

B. It is a confederation AS.

C. It is the AS of a route reflector.

D. It is our own AS.

E. A route map has been applied to this route.

F. The BGP next hop is unreachable.

Answer: B

Explanation:


CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certbus.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certbus.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand Certbus Testking Pass4sure Actualtests Others
Price $45.99 $124.99 $125.99 $189 $69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection
         

Be First to Comment

Leave a Reply