Press "Enter" to skip to content

Free Download the Most Update CertBus Cisco 400-101 Brain Dumps

CertBus 2018 Hottest Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

400-101 CCIE Exam PDF and VCE Dumps : 1436QAs Instant Download: https://www.certbus.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certbus.com/online-pdf/400-101.pdf
☆ CertBus 2018 Hottest 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1436QAs are all new published by Cisco Official Exam Center

100% candidates have passed the CCIE Newest 400-101 study guide exam by the help of CertBus pass guaranteed CCIE Nov 19,2018 Newest 400-101 study guide preparation materials. The CertBus Cisco PDF and VCEs are the latest and cover every knowledge points of CCIE Latest 400-101 pdf dumps CCIE Routing and Switching Written v5.0 certifications. You can try the Q and As for an undeniable success in Latest 400-101 vce dumps exam.

updated 2016 for all 400-101 top certifications | CertBus . CertBus: 400-101 certification training portal. CertBus exam guide: pass the 400-101 exam on your first attempt! CertBus 400-101 certification practice questions and answers. help candidates get well prepared for their 400-101 certification exams. free and latest CertBus exam questions | all CertBus latest microsoft, vmware, comptia, cisco,hp ,citrix and some other hot exams practice tests and questions and answers free download!

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certbus.com/400-101.html

QUESTION NO:2

A branch router is configured with an egress QoS policy that was designed for a total number of

10 concurrent VOIP calls.

Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was

established, all calls were affected and the voice quality was dramatically degraded.

Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS

configuration should be updated due to the new traffic profile?

A. Increase the shaping rate for the priority queue. B.

Remove the policer applied on the priority queue. C.

Remove the shaper applied on the priority queue. D.

Increase the policing rate for the priority queue.

Answer: D

Explanation:


QUESTION NO:4

Refer to the exhibit.

R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes

through both links.

Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for

outgoing traffic (R1 to ISP 2)?

A. Increase local preference on R1 for received routes

B. Decrease local preference on R1 for received routes

C. Increase MED on ISP 2 for received routes

D. Decrease MED on ISP 2 for received routes

Answer: A

Explanation: Explanation

Local preference is an indication to the AS about which path has preference to exit the AS in order

to reach a certain network. A path with higher local preference is preferred more. The default value

of preference is 100.

Reference

http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s

html?

referring_site=smartnavRD


QUESTION NO:5

Refer to the exhibit.

A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used

for the default route, pointing to both interfaces with a different administrative distance, so that one

of the default routes is preferred.

Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.

After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static

route remained active. They lost their Internet connectivity, even though the backup link was

operating.

Which two possible solutions can be implemented to avoid this situation in the future? (Choose

two.)

A. Implement HSRP link tracking on the branch router R1.

B. Use a track object with an IP SLA probe for the static route on R1.

C. Track the link state of the Ethernet link using a track object on R1.

D. Use a routing protocol between R1 and the upstream ISP.

Answer: B,D

Explanation:

Interface Tracking

Interface tracking allows you to specify another interface on the router for the HSRP process to

monitor in order to alter the HSRP priority for a given group.

If the specified interface\’s line protocol goes down, the HSRP priority of this router is reduced,

allowing another HSRP router with higher priority can become active (if it has preemption

enabled).

To configure HSRP interface tracking, use the standby [group] track interface [priority] command.

When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you

explicitly set the decrement value, then the value is decreased by that amount if that interface is

down, and decrements are cumulative. If you do not set an explicit decrement value, then the

value is decreased by 10 for each interface that goes down, and decrements are cumulative.

The following example uses the following configuration, with the default decrement value of 10.

Note: When an HSRP group number is not specified, the default group number is group 0.

interface ethernet0

ip address 10.1.1.1 255.255.255.0

standby ip 10.1.1.3

standby priority 110

standby track serial0

standby track serial1

The HSRP behavior with this configuration is:

0 interfaces down = no decrease (priority is 110)

1 interface down = decrease by 10 (priority becomes100)

2 interfaces down = decrease by 10 (priority becomes 90)

Reference

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i

ntracking


QUESTION NO:6

Why would a rogue host that is running a DHCP server on a campus LAN network present a

security risk?

A. It may allocate IP addresses from an unknown subnet to the users.

B. All multicast traffic can be sniffed by using the DHCP multicast capabilities.

C. The CPU utilization of the first hop router can be overloaded by exploiting DHCP relay open

ports.

D. A potential man-in-the-middle attack can be used against the clients.

Answer: D

Explanation:


QUESTION NO:7

Which statement is true about TCN propagation?

A. The originator of the TCN immediately floods this information through the network.

B. The TCN propagation is a two step process.

C. A TCN is generated and sent to the root bridge.

D. The root bridge must flood this information throughout the network.

Answer: C

Explanation:

Explanation

New Topology Change Mechanisms

When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the

root bridge.

This is shown in this diagram:

Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the

BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge

receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay

seconds. This ensures a relatively quick flush of stale information. Refer to Understanding

Spanning-Tree Protocol Topology Changes for more information on this process. This topology

change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its

propagation through the network evolve.

Topology Change Detection

In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This

means that a loss of connectivity is not considered as a topology change any more, contrary to

802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge

detects a topology change, these occur:

It starts the TC While timer with a value equal to twice the hello-time for all its non-edge

designated ports and its root port, if necessary.

It flushes the MAC addresses associated with all these ports.

Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC

bit set.

BPDUs are also sent on the root port while the timer is active.

Topology Change Propagation

When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:

It clears the MAC addresses learned on all its ports, except the one that receives the topology

change.

It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port

(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).

This way, the TCN floods very quickly across the whole network. The TC propagation is now a one

step process. In fact, the initiator of the topology change floods this information throughout the

network, as opposed to 802.1D where only the root did. This mechanism is much faster than the

802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the

topology change state for the whole network for seconds.

In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of

the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but

on the other hand it clears potential stale information that prevents rapid connectivity restitution.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml


400-101 PDF Dumps400-101 Practice Test400-101 Braindumps

QUESTION NO:8

Which statement is true about loop guard?

A. Loop guard only operates on interfaces that are considered point-to-point by the spanning tree.

B. Loop guard only operates on root ports.

C. Loop guard only operates on designated ports.

D. Loop guard only operates on edge ports.

Answer: A

Explanation:

Explanation

Understanding How Loop Guard Works

Unidirectional link failures may cause a root port or alternate port to become designated as root if

BPDUs are absent. Some software failures may introduce temporary loops in the network. Loop

guard checks if a root port or an alternate root port receives BPDUs. If the port is receiving

BPDUs, loop guard puts the port into an inconsistent state until it starts receiving BPDUs again.

Loop guard isolates the failure and lets spanning tree converge to a stable topology without the

failed link or bridge.

You can enable loop guard per port with the set spantree guard loop command.

Note When you are in MST mode, you can set all the ports on a switch with the set spantree

global-defaults loop-guard command.

When you enable loop guard, it is automatically applied to all of the active instances or VLANs to

which that port belongs. When you disable loop guard, it is disabled for the specified ports.

Disabling loop guard moves all loop-inconsistent ports to the listening state.

If you enable loop guard on a channel and the first link becomes unidirectional, loop guard blocks

the entire channel until the affected port is removed from the channel. Figure 8-6 shows loop

guard in a triangle switch configuration.

Figure 8-6 Triangle Switch Configuration with Loop Guard

Figure 8-6 illustrates the following configuration:

Switches A and B are distribution switches.

Switch C is an access switch.

Loop guard is enabled on ports 3/1 and 3/2 on Switches A, B, and C.

Use loop guard only in topologies where there are blocked ports. Topologies that have no blocked

ports, which are loop free, do not need to enable this feature. Enabling loop guard on a root switch

has no effect but provides protection when a root switch becomes a nonroot switch.

Follow these guidelines when using loop guard:

Do not enable loop guard on PortFast-enabled or dynamic VLAN ports.

Do not enable PortFast on loop guard-enabled ports.

Do not enable loop guard if root guard is enabled.

Do not enable loop guard on ports that are connected to a shared link.

Note: We recommend that you enable loop guard on root ports and alternate root ports on access

switches.

Loop guard interacts with other features as follows:

Loop guard does not affect the functionality of UplinkFast or BackboneFast.

Root guard forces a port to always be designated as the root port. Loop guard is effective only if

the port is a root port or an alternate port. Do not enable loop guard and root guard on a port at the

same time.

PortFast transitions a port into a forwarding state immediately when a link is established. Because

a PortFast-enabled port will not be a root port or alternate port, loop guard and PortFast cannot be

configured on the same port. Assigning dynamic VLAN membership for the port requires that the

port is PortFast enabled. Do not configure a loop guard-enabled port with dynamic VLAN

membership.

If your network has a type-inconsistent port or a PVID-inconsistent port, all BPDUs are dropped

until the misconfiguration is corrected. The port transitions out of the inconsistent state after the

message age expires. Loop guard ignores the message age expiration on type-inconsistent ports

and PVID-inconsistent ports. If the port is already blocked by loop guard, misconfigured BPDUs

that are received on the port make loop guard recover, but the port is moved into the type-

inconsistent state or PVID-inconsistent state.

In high-availability switch configurations, if a port is put into the blocked state by loop guard, it

remains blocked even after a switchover to the redundant supervisor engine. The newly activated

supervisor engine recovers the port only after receiving a BPDU on that port.

Loop guard uses the ports known to spanning tree. Loop guard can take advantage of logical ports

provided by the Port Aggregation Protocol (PAgP). However, to form a channel, all the physical

ports grouped in the channel must have compatible configurations. PAgP enforces uniform

configurations of root guard or loop guard on all the physical ports to form a channel.

These caveats apply to loop guard:


QUESTION NO:15

Which three options are considered in the spanning-tree decision process? (Choose three.)

A. lowest root bridge ID

B. lowest path cost to root bridge

C. lowest sender bridge ID

D. highest port ID

E. highest root bridge ID

F. highest path cost to root bridge

Answer: A,B,C

Explanation:

Configuration bridge protocol data units (BPDUs) are sent between switches for each port.

Switches use s four step process to save a copy of the best BPDU seen on every port. When a

port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds

(default), it begins sending them again.

Step 1 Lowest Root Bridge ID (BID)

Step 2 Lowest Path Cost to Root Bridge

Step 3 Lowest Sender BID

Step 4 Lowest Port ID

Reference

Cisco General Networking Theory Quick Reference Sheets


QUESTION NO:17

Which three combinations are valid LACP configurations that will set up a channel? (Choose

three.)

A. On/On

B. On/Auto

C. Passive/Active

D. Desirable/Auto

E. Active/Active

F. Desirable/Desirable

Answer: A,C,E

Explanation:


QUESTION NO:19

Which two options does Cisco PfR use to control the entrance link selection with inbound

optimization? (Choose two.)

A. Prepend extra AS hops to the BGP prefix.

B. Advertise more specific BGP prefixes (longer mask).

C. Add (prepend) one or more communities to the prefix that is advertised by BGP.

D. Have BGP dampen the prefix.

Answer: A,C

Explanation: PfR Entrance Link Selection Control Techniques

The PfR BGP inbound optimization feature introduced the ability to influence inbound traffic. A

network advertises reachability of its inside prefixes to the Internet using eBGP advertisements to

its ISPs. If the same prefix is advertised to more than one ISP, then the network is multihoming.

PfR BGP inbound optimization works best with multihomed networks, but it can also be used with

a network that has multiple connections to the same ISP. To implement BGP inbound

optimization, PfR manipulates eBGP advertisements to influence the best entrance selection for

traffic bound for inside prefixes. The benefit of implementing the best entrance selection is limited

to a network that has more than one ISP connection.

To enforce an entrance link selection, PfR offers the following methods:

BGP Autonomous System Number Prepend When an entrance link goes out-of-policy (OOP) due

to delay, or in images prior to Cisco IOS Releases 15.2(1) T1 and 15.1(2)S, and PfR selects a

best entrance for an inside prefix, extra autonomous system hops are prepended one at a time (up

to a maximum of six) to the inside prefix BGP advertisement over the other entrances. In Cisco

IOS Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of policy

(OOP) due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix,

six extra autonomous system hops are prepended immediately to the inside prefix BGP

advertisement over the other entrances. The extra autonomous system hops on the other

entrances increase the probability that the best entrance will be used for the inside prefix. When

the entrance link is OOP due to unreachable or loss reasons, six extra autonomous system hops

are added immediately to allow the software to quickly move the traffic away from the old entrance

link. This is the default method PfR uses to control an inside prefix, and no user configuration is

required.

BGP Autonomous System Number Community Prepend

When an entrance link goes out-of-policy (OOP) due to delay, or in images prior to Cisco IOS

Releases 15.2

(1)T1 and 15.1(2)S, and PfR selects a best entrance for an inside prefix, a BGP prepend

community is attached one at a time (up to a maximum of six) to the inside prefix BGP

advertisement from the network to another autonomous system such as an ISP. In Cisco IOS

Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of-policy (OOP)

due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix, six BGP

prepend communities are attached to the inside prefix BGP advertisement. The BGP prepend

community will increase the number of autonomous system hops in the advertisement of the

inside prefix from the ISP to its peers. Autonomous system prepend BGP community is the

preferred method to be used for PfR BGP inbound optimization because there is no risk of the

local ISP filtering the extra autonomous system hops. There are some issues, for example, not all

ISPs support the BGP prepend community, ISP policies may ignore or modify the autonomous

system hops, and a transit ISP may filter the autonomous system path. If you use this method of

inbound optimization and a change is made to an autonomous system, you must issue an

outbound reconfiguration using the “clear ip bgp” command.

Reference

http://www.cisco.com/en/US/docs/ios-xml/ios/pfr/configuration/15-2s/pfr-bgp-inbound.html#GUID-

F8A59E241D59-

4924-827D-B23B43D9A8E0

http://www.cisco.com/en/US/products/ps8787/products_ios_protocol_option_home.html


QUESTION NO:23

What action will a BGP route reflector take when it receives a prefix marked with the community

attribute NO ADVERTISE from a client peer?

A. It will advertise the prefix to all other client peers and non-client peers.

B. It will not advertise the prefix to EBGP peers.

C. It will only advertise the prefix to all other IBGP peers.

D. It will not advertise the prefix to any peers.

Answer: D

Explanation:


CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certbus.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certbus.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand Certbus Testking Pass4sure Actualtests Others
Price $45.99 $124.99 $125.99 $189 $69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection
         

Be First to Comment

Leave a Reply