[Newest Version] Free CertBus Cisco 400-101 PDF and Exam Questions Download 100% Pass Exam

CertBus 2018 Real Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

☆ 400-101 CCIE Exam PDF and VCE Dumps : 1063QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Real 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1063QAs are all new published by Cisco Official Exam Center

Do not worry about that if you are stuck in the CCIE Hotest 400-101 vce dumps exam difficulties, CertBus will assist you all your way through the CCIE Latest 400-101 vce dumps CCIE Routing and Switching Written v5.0 exam with the most update CCIE Hotest 400-101 study guide PDF and VCE dumps. CertBus exam Latest 400-101 vce dumps preparation materials are the most comprehensive material, covering every key knowledge of Mar 30,2018 Hotest 400-101 vce CCIE Routing and Switching Written v5.0 exam.

CertBus: best 400-101 certification material provider are cheapest in the market! you are only successful with 400-101 testing engine in your it certification – CertBus! 400-101 exam study material and study tips from CertBus. CertBus – the most professional provider of all 400-101 certifications. pass all the 400-101 exam easily.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html

QUESTION NO:7

Which statement is true about TCN propagation?

A. The originator of the TCN immediately floods this information through the network.

B. The TCN propagation is a two step process.

C. A TCN is generated and sent to the root bridge.

D. The root bridge must flood this information throughout the network.

Answer: C

Explanation:

Explanation

New Topology Change Mechanisms

When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the

root bridge.

This is shown in this diagram:

Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the

BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge

receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay

seconds. This ensures a relatively quick flush of stale information. Refer to Understanding

Spanning-Tree Protocol Topology Changes for more information on this process. This topology

change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its

propagation through the network evolve.

Topology Change Detection

In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This

means that a loss of connectivity is not considered as a topology change any more, contrary to

802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge

detects a topology change, these occur:

It starts the TC While timer with a value equal to twice the hello-time for all its non-edge

designated ports and its root port, if necessary.

It flushes the MAC addresses associated with all these ports.

Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC

bit set.

BPDUs are also sent on the root port while the timer is active.

Topology Change Propagation

When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:

It clears the MAC addresses learned on all its ports, except the one that receives the topology

change.

It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port

(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).

This way, the TCN floods very quickly across the whole network. The TC propagation is now a one

step process. In fact, the initiator of the topology change floods this information throughout the

network, as opposed to 802.1D where only the root did. This mechanism is much faster than the

802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the

topology change state for the whole network for seconds.

In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of

the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but

on the other hand it clears potential stale information that prevents rapid connectivity restitution.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

QUESTION NO:16

In 802.1s, how is the VLAN to instance mapping represented in the BPDU?

A. The VLAN to instance mapping is a normal 16-byte field in the MST BPDU.

B. The VLAN to instance mapping is a normal 12-byte field in the MST BPDU.

C. The VLAN to instance mapping is a 16-byte MD5 signature field in the MST BPDU.

D. The VLAN to instance mapping is a 12-byte MD5 signature field in the MST BPDU.

Answer: C

Explanation:

MST Configuration and MST Region

Each switch running MST in the network has a single MST configuration that consists of these

three attributes:

1. An alphanumeric configuration name (32 bytes)

2. A configuration revision number (two bytes)

3. A 4096-element table that associates each of the potential 4096 VLANs supported on the

chassis to a given instance.

In order to be part of a common MST region, a group of switches must share the same

configuration attributes.

It is up to the network administrator to properly propagate the configuration throughout the region.

Currently, this step is only possible by the means of the command line interface (CLI) or through

Simple Network

Management Protocol (SNMP). Other methods can be envisioned, as the IEEE specification does

not explicitly mention how to accomplish that step.

Note: If for any reason two switches differ on one or more configuration attribute, the switches are

part of different regions. For more information refer to the Region Boundary section of this

document.

Region Boundary

In order to ensure consistent VLAN-to-instance mapping, it is necessary for the protocol to be able

to exactly identify the boundaries of the regions. For that purpose, the characteristics of the region

are included in the BPDUs. The exact VLANs-to-instance mapping is not propagated in the BPDU,

because the switches only need to know whether they are in the same region as a neighbor.

Therefore, only a digest of the VLANs-toinstance mapping table is sent, along with the revision

number and the name. Once a switch receives a BPDU, the switch extracts the digest (a

numerical value derived from the VLAN-to-instance mapping table through a mathematical

function) and compares this digest with its own computed digest. If the digests differ, the port on

which the BPDU was received is at the boundary of a region.

In generic terms, a port is at the boundary of a region if the designated bridge on its segment is in

a different region or if it receives legacy 802.1d BPDUs. In this diagram, the port on B1 is at the

boundary of region A, whereas the ports on B2 and B3 are internal to region B:

MST Instances

According to the IEEE 802.1s specification, an MST bridge must be able to handle at least these

two instances:

One Internal Spanning Tree (IST)

One or more Multiple Spanning Tree Instance(s) (MSTIs)

The terminology continues to evolve, as 802.1s is actually in a pre-standard phase. It is likely

these names will change in the final release of 802.1s. The Cisco implementation supports 16

instances: one IST (instance 0) and 15 MSTIs.

show vtp status

Cisco switches “show vtp status” Field Descriptions has a MD5 digest field that is a 16-byte

checksum of the

VTP configuration as shown below

Router# show vtp status

VTP Version: 3 (capable)

Configuration Revision: 1

Maximum VLANs supported locally: 1005

Number of existing VLANs: 37

VTP Operating Mode: Server

VTP Domain Name: [smartports]

VTP Pruning Mode: Disabled

VTP V2 Mode: Enabled

VTP Traps Generation: Disabled

MD5 digest : 0x26 0xEE 0x0D 0x84 0x73 0x0E 0x1B 0x69

Configuration last modified by 172.20.52.19 at 7-25-08 14:33:43

Local updater ID is 172.20.52.19 on interface Gi5/2 (first layer3 interface fou)

VTP version running: 2

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfc.shtml

http://www.cisco.com/en/US/docs/ios-xml/ios/lanswitch/command/lsw-cr-book.pdf

QUESTION NO:19

Which two options does Cisco PfR use to control the entrance link selection with inbound

optimization? (Choose two.)

A. Prepend extra AS hops to the BGP prefix.

B. Advertise more specific BGP prefixes (longer mask).

C. Add (prepend) one or more communities to the prefix that is advertised by BGP.

D. Have BGP dampen the prefix.

Answer: A,C

Explanation: PfR Entrance Link Selection Control Techniques

The PfR BGP inbound optimization feature introduced the ability to influence inbound traffic. A

network advertises reachability of its inside prefixes to the Internet using eBGP advertisements to

its ISPs. If the same prefix is advertised to more than one ISP, then the network is multihoming.

PfR BGP inbound optimization works best with multihomed networks, but it can also be used with

a network that has multiple connections to the same ISP. To implement BGP inbound

optimization, PfR manipulates eBGP advertisements to influence the best entrance selection for

traffic bound for inside prefixes. The benefit of implementing the best entrance selection is limited

to a network that has more than one ISP connection.

To enforce an entrance link selection, PfR offers the following methods:

BGP Autonomous System Number Prepend When an entrance link goes out-of-policy (OOP) due

to delay, or in images prior to Cisco IOS Releases 15.2(1) T1 and 15.1(2)S, and PfR selects a

best entrance for an inside prefix, extra autonomous system hops are prepended one at a time (up

to a maximum of six) to the inside prefix BGP advertisement over the other entrances. In Cisco

IOS Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of policy

(OOP) due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix,

six extra autonomous system hops are prepended immediately to the inside prefix BGP

advertisement over the other entrances. The extra autonomous system hops on the other

entrances increase the probability that the best entrance will be used for the inside prefix. When

the entrance link is OOP due to unreachable or loss reasons, six extra autonomous system hops

are added immediately to allow the software to quickly move the traffic away from the old entrance

link. This is the default method PfR uses to control an inside prefix, and no user configuration is

required.

BGP Autonomous System Number Community Prepend

When an entrance link goes out-of-policy (OOP) due to delay, or in images prior to Cisco IOS

Releases 15.2

(1)T1 and 15.1(2)S, and PfR selects a best entrance for an inside prefix, a BGP prepend

community is attached one at a time (up to a maximum of six) to the inside prefix BGP

advertisement from the network to another autonomous system such as an ISP. In Cisco IOS

Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of-policy (OOP)

due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix, six BGP

prepend communities are attached to the inside prefix BGP advertisement. The BGP prepend

community will increase the number of autonomous system hops in the advertisement of the

inside prefix from the ISP to its peers. Autonomous system prepend BGP community is the

preferred method to be used for PfR BGP inbound optimization because there is no risk of the

local ISP filtering the extra autonomous system hops. There are some issues, for example, not all

ISPs support the BGP prepend community, ISP policies may ignore or modify the autonomous

system hops, and a transit ISP may filter the autonomous system path. If you use this method of

inbound optimization and a change is made to an autonomous system, you must issue an

outbound reconfiguration using the “clear ip bgp” command.

Reference

http://www.cisco.com/en/US/docs/ios-xml/ios/pfr/configuration/15-2s/pfr-bgp-inbound.html#GUID-

F8A59E241D59-

4924-827D-B23B43D9A8E0

http://www.cisco.com/en/US/products/ps8787/products_ios_protocol_option_home.html

QUESTION NO:20

Refer to the exhibit.

What is the potential issue with this configuration?

A. There is no potential issue; OSPF will work fine in any condition.

B. Sub-optimal routing may occur since there is no area 1 adjacency between the ABRs.

C. This is a wrong OSPF configuration because all routers must be in area 0 only.

D. This is a wrong OSPF configuration because /30 requires 0.0.0.3 wild card.

Answer: B

Explanation:

QUESTION NO:23

What action will a BGP route reflector take when it receives a prefix marked with the community

attribute NO ADVERTISE from a client peer?

A. It will advertise the prefix to all other client peers and non-client peers.

B. It will not advertise the prefix to EBGP peers.

C. It will only advertise the prefix to all other IBGP peers.

D. It will not advertise the prefix to any peers.

Answer: D

Explanation:

400-101 PDF Dumps400-101 Exam Questions400-101 Braindumps

QUESTION NO:24

Refer to the exhibit.

R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).

What can be done so that R1 will learn about this network?

A. Disable auto-summary on R2.

B. Configure an explicit network command for the 172.16.10.0 subnet on R2.

C. Subnet information cannot be passed between IBGP peers.

D. Disable auto-summary on R1.

Answer: B

Explanation:

By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet

routes in BGP, use an explicit network command or the no auto-summary command. If you disable

auto-summarization and have not entered a network command, you will not advertise network

routes for networks with subnet routes unless they contain a summary route.

Reference

http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html

QUESTION NO:30

What is the flooding scope of an OSPFv3 LSA, if the value of the S2 bit is set to 1 and the S1 bit is

set to 0?

A. link local

B. area wide

C. AS wide

D. reserved

Answer: C

Explanation:

The Type 1 router LSA is now link local and the Type 2 Network LSA is AS Wide

S2 and S1 indicate the LSA’s flooding scope. Table 9-1 shows the possible values of these two

bits and the associated flooding scopes.

Table 9-1 S bits in the OSPFv3 LSA Link State Type field and their associated flooding scopes

LSA Function Code, the last 13 bits of the LS Type field, corresponds to the OSPFv2 Type field.

Table 9-2 shows the common LSA types used by OSPFv3 and the values of their corresponding

LS Types. If you decode the hex values, you will see that the default U bit of all of them is 0. The S

bits of all LSAs except two indicate area scope. Of the remaining two, AS External LSAs have an

AS flooding scope and Link LSAs have a linklocal flooding scope. Most of the OSPFv3 LSAs have

functional counterparts in OSPFv2; these OSPFv2 LSAs and their types are also shown in Table

9-2.

Table 9-2 OSPFv3 LSA types and their OSPFv2 counterparts

Reference

http://www.networkworld.com/subnets/cisco/050107-ch9-ospfv3.html?page=1

QUESTION NO:31

How will EIGRPv6 react if there is an IPv6 subnet mask mismatch between the Global Unicast

addresses on a point-to-point link?

A. EIGRPv6 will form a neighbor relationship.

B. EIGRPv6 will not form a neighbor relationship.

C. EIGRPv6 will form a neighbor relationship, but with the log MSG: “EIGRPv6 neighbor not on a

common subnet.”

D. EIGRPv6 will form a neighbor relationship, but routes learned from that neighbor will not be

installed in the routing table.

Answer: A Explanation:

http://www.ietf.org/rfc/rfc3587.txt

QUESTION NO:36

For which routes does LDP advertise a label binding?

A. all routes in the routing table

B. only the IGP and BGP routes in the routing table

C. only the BGP routes in the routing table

D. only the IGP routes in the routing table

Answer: D

Explanation:

QUESTION NO:39

Which two statements are correct about Nonstop Forwarding? (Choose two.)

A. It allows the standby RP to take control of the device after a hardware or software fault on the

active RP.

B. It is a Layer 3 function that works with SSO to minimize the amount of time a network is

unavailable to users following a switchover.

C. It is supported by the implementation of EIGRP, OSPF, RIPv2, and BGP protocols.

D. It synchronizes startup configuration, startup variables, and running configuration.

E. The main objective of NSF is to continue forwarding IP packets following a switchover.

F. Layer 2 802.1w or 802.1s must be used, as 802.1d cannot process the Layer 2 changes.

G. Routing protocol tuning parameters must be the same as the NSF parameters, or failover will

be inconsistent.

Answer: B,E

Explanation: Explanation

Cisco Nonstop Forwarding (NSF) works with the Stateful Switchover (SSO) feature in Cisco IOS

software. NSF works with SSO to minimize the amount of time a network is unavailable to its

users following a switchover. The main objective of Cisco NSF is to continue forwarding IP

packets following a Route Processor (RP) switchover.

Reference

http://www.cisco.com/en/US/docs/ios/12_2s/feature/guide/fsnsf20s.html

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection