As a leading IT exam study material provider, CertBus not only provides you the 350-001 exam questions and answers but also the most comprehensive knowledge of the whole CCIE 350-001 CCIE Routing and Switching Written certifications. We provide our users with the most accurate 350-001 CCIE Routing and Switching Written study material about the CCIE 350-001 exam and the guarantee of pass. We assist you to get well prepared for CCIE 350-001 certification which is regarded valuable the IT sector.
We CertBus has our own expert team. They selected and published the latest 350-001 preparation materials from Cisco Official Exam-Center: http://www.certgod.com/350-001.html
QUESTION NO:5
Refer to the exhibit.
A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used
for the default route, pointing to both interfaces with a different administrative distance, so that one
of the default routes is preferred.
Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.
After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static
route remained active. They lost their Internet connectivity, even though the backup link was
operating.
Which two possible solutions can be implemented to avoid this situation in the future? (Choose
two.)
A. Implement HSRP link tracking on the branch router R1.
B. Use a track object with an IP SLA probe for the static route on R1.
C. Track the link state of the Ethernet link using a track object on R1.
D. Use a routing protocol between R1 and the upstream ISP.
Answer: B,D
Explanation:
Interface Tracking
Interface tracking allows you to specify another interface on the router for the HSRP process to
monitor in order to alter the HSRP priority for a given group.
If the specified interface’s line protocol goes down, the HSRP priority of this router is reduced,
allowing another HSRP router with higher priority can become active (if it has preemption
enabled).
To configure HSRP interface tracking, use the standby [group] track interface [priority] command.
When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you
explicitly set the decrement value, then the value is decreased by that amount if that interface is
down, and decrements are cumulative. If you do not set an explicit decrement value, then the
value is decreased by 10 for each interface that goes down, and decrements are cumulative.
The following example uses the following configuration, with the default decrement value of 10.
Note: When an HSRP group number is not specified, the default group number is group 0.
interface ethernet0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.3
standby priority 110
standby track serial0
standby track serial1
The HSRP behavior with this configuration is:
0 interfaces down = no decrease (priority is 110)
1 interface down = decrease by 10 (priority becomes100)
2 interfaces down = decrease by 10 (priority becomes 90)
Reference
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i
ntracking
QUESTION NO:11
When you are troubleshooting duplex mismatches, which two errors are typically seen on the full-
duplex end? (Choose two.)
A. runts
B. FCS errors
C. interface resets
D. late collisions
Answer: A,B
Explanation:
QUESTION NO:12
Which two options are contained in a VTP subset advertisement? (Choose two.)
A. followers field
B. MD5 digest
C. VLAN information
D. sequence number
Answer: C,D
Explanation:
Subset Advertisements
When you add, delete, or change a VLAN in a Catalyst, the server Catalyst where the changes are
made increments the configuration revision and issues a summary advertisement. One or several
subset advertisements follow the summary advertisement. A subset advertisement contains a list
of VLAN information.
If there are several VLANs, more than one subset advertisement can be required in order to
advertise all the VLANs.
Subset Advertisement Packet Format
This formatted example shows that each VLAN information field contains information for a different
VLAN. It is ordered so that lowered-valued ISL VLAN IDs occur first:
Most of the fields in this packet are easy to understand. These are two clarifications:
Code
QUESTION NO:22
Refer to the exhibit.
Which path is selected as best path?
A. path 1, because it is learned from IGP B.
path 1, because the metric is the lowest C.
path 2, because it is external
D. path 2, because it has the higher router ID
Answer: B
Explanation:
QUESTION NO:7
Which statement is true about TCN propagation?
A. The originator of the TCN immediately floods this information through the network.
B. The TCN propagation is a two step process.
C. A TCN is generated and sent to the root bridge.
D. The root bridge must flood this information throughout the network.
Answer: C
Explanation:
Explanation
New Topology Change Mechanisms
When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the
root bridge.
This is shown in this diagram:
Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the
BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge
receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay
seconds. This ensures a relatively quick flush of stale information. Refer to Understanding
Spanning-Tree Protocol Topology Changes for more information on this process. This topology
change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its
propagation through the network evolve.
Topology Change Detection
In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This
means that a loss of connectivity is not considered as a topology change any more, contrary to
802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge
detects a topology change, these occur:
It starts the TC While timer with a value equal to twice the hello-time for all its non-edge
designated ports and its root port, if necessary.
It flushes the MAC addresses associated with all these ports.
Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC
bit set.
BPDUs are also sent on the root port while the timer is active.
Topology Change Propagation
When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:
It clears the MAC addresses learned on all its ports, except the one that receives the topology
change.
It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port
(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).
This way, the TCN floods very quickly across the whole network. The TC propagation is now a one
step process. In fact, the initiator of the topology change floods this information throughout the
network, as opposed to 802.1D where only the root did. This mechanism is much faster than the
802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the
topology change state for the whole network for seconds.
In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of
the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but
on the other hand it clears potential stale information that prevents rapid connectivity restitution.
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
QUESTION NO:19
Which two options does Cisco PfR use to control the entrance link selection with inbound
optimization? (Choose two.)
A. Prepend extra AS hops to the BGP prefix.
B. Advertise more specific BGP prefixes (longer mask).
C. Add (prepend) one or more communities to the prefix that is advertised by BGP.
D. Have BGP dampen the prefix.
Answer: A,C
Explanation: PfR Entrance Link Selection Control Techniques
The PfR BGP inbound optimization feature introduced the ability to influence inbound traffic. A
network advertises reachability of its inside prefixes to the Internet using eBGP advertisements to
its ISPs. If the same prefix is advertised to more than one ISP, then the network is multihoming.
PfR BGP inbound optimization works best with multihomed networks, but it can also be used with
a network that has multiple connections to the same ISP. To implement BGP inbound
optimization, PfR manipulates eBGP advertisements to influence the best entrance selection for
traffic bound for inside prefixes. The benefit of implementing the best entrance selection is limited
to a network that has more than one ISP connection.
To enforce an entrance link selection, PfR offers the following methods:
BGP Autonomous System Number Prepend When an entrance link goes out-of-policy (OOP) due
to delay, or in images prior to Cisco IOS Releases 15.2(1) T1 and 15.1(2)S, and PfR selects a
best entrance for an inside prefix, extra autonomous system hops are prepended one at a time (up
to a maximum of six) to the inside prefix BGP advertisement over the other entrances. In Cisco
IOS Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of policy
(OOP) due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix,
six extra autonomous system hops are prepended immediately to the inside prefix BGP
advertisement over the other entrances. The extra autonomous system hops on the other
entrances increase the probability that the best entrance will be used for the inside prefix. When
the entrance link is OOP due to unreachable or loss reasons, six extra autonomous system hops
are added immediately to allow the software to quickly move the traffic away from the old entrance
link. This is the default method PfR uses to control an inside prefix, and no user configuration is
required.
BGP Autonomous System Number Community Prepend
When an entrance link goes out-of-policy (OOP) due to delay, or in images prior to Cisco IOS
Releases 15.2
(1)T1 and 15.1(2)S, and PfR selects a best entrance for an inside prefix, a BGP prepend
community is attached one at a time (up to a maximum of six) to the inside prefix BGP
advertisement from the network to another autonomous system such as an ISP. In Cisco IOS
Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of-policy (OOP)
due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix, six BGP
prepend communities are attached to the inside prefix BGP advertisement. The BGP prepend
community will increase the number of autonomous system hops in the advertisement of the
inside prefix from the ISP to its peers. Autonomous system prepend BGP community is the
preferred method to be used for PfR BGP inbound optimization because there is no risk of the
local ISP filtering the extra autonomous system hops. There are some issues, for example, not all
ISPs support the BGP prepend community, ISP policies may ignore or modify the autonomous
system hops, and a transit ISP may filter the autonomous system path. If you use this method of
inbound optimization and a change is made to an autonomous system, you must issue an
outbound reconfiguration using the “clear ip bgp” command.
Reference
http://www.cisco.com/en/US/docs/ios-xml/ios/pfr/configuration/15-2s/pfr-bgp-inbound.html#GUID-
F8A59E241D59-
4924-827D-B23B43D9A8E0
http://www.cisco.com/en/US/products/ps8787/products_ios_protocol_option_home.html
QUESTION NO:2
A branch router is configured with an egress QoS policy that was designed for a total number of
10 concurrent VOIP calls.
Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was
established, all calls were affected and the voice quality was dramatically degraded.
Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS
configuration should be updated due to the new traffic profile?
A. Increase the shaping rate for the priority queue. B.
Remove the policer applied on the priority queue. C.
Remove the shaper applied on the priority queue. D.
Increase the policing rate for the priority queue.
Answer: D
Explanation:
QUESTION NO:24
Refer to the exhibit.
R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).
What can be done so that R1 will learn about this network?
A. Disable auto-summary on R2.
B. Configure an explicit network command for the 172.16.10.0 subnet on R2.
C. Subnet information cannot be passed between IBGP peers.
D. Disable auto-summary on R1.
Answer: B
Explanation:
By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet
routes in BGP, use an explicit network command or the no auto-summary command. If you disable
auto-summarization and have not entered a network command, you will not advertise network
routes for networks with subnet routes unless they contain a summary route.
Reference
http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html
QUESTION NO:17
Which three combinations are valid LACP configurations that will set up a channel? (Choose
three.)
A. On/On
B. On/Auto
C. Passive/Active
D. Desirable/Auto
E. Active/Active
F. Desirable/Desirable
Answer: A,C,E
Explanation:
QUESTION NO:26
Refer to the exhibit.
Why is AS 65333 in parentheses?
A. It is an external AS.
B. It is a confederation AS.
C. It is the AS of a route reflector.
D. It is our own AS.
E. A route map has been applied to this route.
F. The BGP next hop is unreachable.
Answer: B
Explanation:
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 350-001 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written exam dumps will help you to be the Cisco specialist, clear your 350-001 exam and get the final success.
350-001 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mUVBtM1piOS1IMEU/view?usp=sharing
350-001 Cisco exam dumps (100% Pass Guaranteed) from CertBus: http://www.certgod.com/350-001.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.