[Newest Version] Free CertBus Cisco 350-001 PDF and Exam Questions Download 100% Pass Exam

100% candidates have passed the CCIE 350-001 exam by the help of CertBus pass guaranteed CCIE 350-001 preparation materials. The CertBus Cisco PDF and VCEs are the latest and cover every knowledge points of CCIE 350-001 CCIE Routing and Switching Written certifications. You can try the Q and As for an undeniable success in 350-001 exam.

We CertBus has our own expert team. They selected and published the latest 350-001 preparation materials from Cisco Official Exam-Center: http://www.certgod.com/350-001.html

QUESTION NO:24

Refer to the exhibit.

R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).

What can be done so that R1 will learn about this network?

A. Disable auto-summary on R2.

B. Configure an explicit network command for the 172.16.10.0 subnet on R2.

C. Subnet information cannot be passed between IBGP peers.

D. Disable auto-summary on R1.

Answer: B

Explanation:

By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet

routes in BGP, use an explicit network command or the no auto-summary command. If you disable

auto-summarization and have not entered a network command, you will not advertise network

routes for networks with subnet routes unless they contain a summary route.

Reference

http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html

QUESTION NO:2

A branch router is configured with an egress QoS policy that was designed for a total number of

10 concurrent VOIP calls.

Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was

established, all calls were affected and the voice quality was dramatically degraded.

Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS

configuration should be updated due to the new traffic profile?

A. Increase the shaping rate for the priority queue. B.

Remove the policer applied on the priority queue. C.

Remove the shaper applied on the priority queue. D.

Increase the policing rate for the priority queue.

Answer: D

Explanation:

QUESTION NO:23

What action will a BGP route reflector take when it receives a prefix marked with the community

attribute NO ADVERTISE from a client peer?

A. It will advertise the prefix to all other client peers and non-client peers.

B. It will not advertise the prefix to EBGP peers.

C. It will only advertise the prefix to all other IBGP peers.

D. It will not advertise the prefix to any peers.

Answer: D

Explanation:

QUESTION NO:8

Which statement is true about loop guard?

A. Loop guard only operates on interfaces that are considered point-to-point by the spanning tree.

B. Loop guard only operates on root ports.

C. Loop guard only operates on designated ports.

D. Loop guard only operates on edge ports.

Answer: A

Explanation:

Explanation

Understanding How Loop Guard Works

Unidirectional link failures may cause a root port or alternate port to become designated as root if

BPDUs are absent. Some software failures may introduce temporary loops in the network. Loop

guard checks if a root port or an alternate root port receives BPDUs. If the port is receiving

BPDUs, loop guard puts the port into an inconsistent state until it starts receiving BPDUs again.

Loop guard isolates the failure and lets spanning tree converge to a stable topology without the

failed link or bridge.

You can enable loop guard per port with the set spantree guard loop command.

Note When you are in MST mode, you can set all the ports on a switch with the set spantree

global-defaults loop-guard command.

When you enable loop guard, it is automatically applied to all of the active instances or VLANs to

which that port belongs. When you disable loop guard, it is disabled for the specified ports.

Disabling loop guard moves all loop-inconsistent ports to the listening state.

If you enable loop guard on a channel and the first link becomes unidirectional, loop guard blocks

the entire channel until the affected port is removed from the channel. Figure 8-6 shows loop

guard in a triangle switch configuration.

Figure 8-6 Triangle Switch Configuration with Loop Guard

Figure 8-6 illustrates the following configuration:

Switches A and B are distribution switches.

Switch C is an access switch.

Loop guard is enabled on ports 3/1 and 3/2 on Switches A, B, and C.

Use loop guard only in topologies where there are blocked ports. Topologies that have no blocked

ports, which are loop free, do not need to enable this feature. Enabling loop guard on a root switch

has no effect but provides protection when a root switch becomes a nonroot switch.

Follow these guidelines when using loop guard:

Do not enable loop guard on PortFast-enabled or dynamic VLAN ports.

Do not enable PortFast on loop guard-enabled ports.

Do not enable loop guard if root guard is enabled.

Do not enable loop guard on ports that are connected to a shared link.

Note: We recommend that you enable loop guard on root ports and alternate root ports on access

switches.

Loop guard interacts with other features as follows:

Loop guard does not affect the functionality of UplinkFast or BackboneFast.

Root guard forces a port to always be designated as the root port. Loop guard is effective only if

the port is a root port or an alternate port. Do not enable loop guard and root guard on a port at the

same time.

PortFast transitions a port into a forwarding state immediately when a link is established. Because

a PortFast-enabled port will not be a root port or alternate port, loop guard and PortFast cannot be

configured on the same port. Assigning dynamic VLAN membership for the port requires that the

port is PortFast enabled. Do not configure a loop guard-enabled port with dynamic VLAN

membership.

If your network has a type-inconsistent port or a PVID-inconsistent port, all BPDUs are dropped

until the misconfiguration is corrected. The port transitions out of the inconsistent state after the

message age expires. Loop guard ignores the message age expiration on type-inconsistent ports

and PVID-inconsistent ports. If the port is already blocked by loop guard, misconfigured BPDUs

that are received on the port make loop guard recover, but the port is moved into the type-

inconsistent state or PVID-inconsistent state.

In high-availability switch configurations, if a port is put into the blocked state by loop guard, it

remains blocked even after a switchover to the redundant supervisor engine. The newly activated

supervisor engine recovers the port only after receiving a BPDU on that port.

Loop guard uses the ports known to spanning tree. Loop guard can take advantage of logical ports

provided by the Port Aggregation Protocol (PAgP). However, to form a channel, all the physical

ports grouped in the channel must have compatible configurations. PAgP enforces uniform

configurations of root guard or loop guard on all the physical ports to form a channel.

These caveats apply to loop guard:

QUESTION NO:6

Why would a rogue host that is running a DHCP server on a campus LAN network present a

security risk?

A. It may allocate IP addresses from an unknown subnet to the users.

B. All multicast traffic can be sniffed by using the DHCP multicast capabilities.

C. The CPU utilization of the first hop router can be overloaded by exploiting DHCP relay open

ports.

D. A potential man-in-the-middle attack can be used against the clients.

Answer: D

Explanation:

QUESTION NO:22

Refer to the exhibit.

Which path is selected as best path?

A. path 1, because it is learned from IGP B.

path 1, because the metric is the lowest C.

path 2, because it is external

D. path 2, because it has the higher router ID

Answer: B

Explanation:

QUESTION NO:15

Which three options are considered in the spanning-tree decision process? (Choose three.)

A. lowest root bridge ID

B. lowest path cost to root bridge

C. lowest sender bridge ID

D. highest port ID

E. highest root bridge ID

F. highest path cost to root bridge

Answer: A,B,C

Explanation:

Configuration bridge protocol data units (BPDUs) are sent between switches for each port.

Switches use s four step process to save a copy of the best BPDU seen on every port. When a

port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds

(default), it begins sending them again.

Step 1 Lowest Root Bridge ID (BID)

Step 2 Lowest Path Cost to Root Bridge

Step 3 Lowest Sender BID

Step 4 Lowest Port ID

Reference

Cisco General Networking Theory Quick Reference Sheets

QUESTION NO:1

Which two commands are required to enable multicast on a router, knowing that the receivers only

support IGMPv2? (Choose two.)

A. ip pim rp-address

B. ip pim ssm

C. ip pim sparse-mode

D. ip pim passive

Answer: A,C

Explanation:

Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode

it is supposed that in every network there is someone who is requesting the multicast traffic so

PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from

where a prune message is received to eliminate the

QUESTION NO:14

Which three options are features of VTP version 3? (Choose three.)

A. VTPv3 supports 8K VLANs.

B. VTPv3 supports private VLAN mapping.

C. VTPv3 allows for domain discovery.

D. VTPv3 uses a primary server concept to avoid configuration revision issues.

E. VTPv3 is not compatible with VTPv1 or VTPv2.

F. VTPv3 has a hidden password option.

Answer: B,D,F

Explanation:

Key Benefits of VTP Version 3

Much work has gone into improving the usability of VTP version 3 in three major areas:

The new version of VTP offers better administrative control over which device is allowed to update

other devices’ view of the VLAN topology. The chance of unintended and disruptive changes is

significantly reduced, and availability is increased. The reduced risk of unintended changes will

ease the change process and help speed deployment.

Functionality for the VLAN environment has been significantly expanded. Two enhancements are

most beneficial for today’s networks:

QUESTION NO:9

Which two are effects of connecting a network segment that is running 802.1D to a network

segment that is running 802.1w? (Choose two.)

A. The entire network switches to 802.1D and generates BPDUs to determine root bridge status. B.

A migration delay of three seconds occurs when the port that is connected to the 802.1D bridge

comes up.

C. The entire network reconverges and a unique root bridge for the 802.1D segment, and a root

bridge for the 802.1w segment, is chosen.

D. The first hop 802.1w switch that is connected to the 802.1D runs entirely in 802.1D compatibility

mode and converts the BPDUs to either 802.1D or 802.1w BPDUs to the 802.1D or 802.1w

segments of the network.

E. Classic 802.1D timers, such as forward delay and max-age, will only be used as a backup, and

will not be necessary if point-to-point links and edge ports are properly identified and set by the

administrator.

Answer: B,E

Explanation:

Each port maintains a variable that defines the protocol to run on the corresponding segment. A

migration delay timer of three seconds also starts when the port comes up. When this timer runs,

the current STP or RSTP mode associated to the port is locked. As soon as the migration delay

expires, the port adapts to the mode that corresponds to the next BPDU it receives. If the port

changes its mode of operation as a result of a BPDU received, the migration delay restarts.

802.1D works by the concept that the protocol had to wait for the network to converge before it

transitioned a port into the forwarding state. With Rapid Spanning Tree it does not have to rely on

any timers, the only variables that that it relies on is edge ports and link types.

Any uplink port that has an alternate port to the root can be directly placed into the forwarding

state (This is the Rapid convergence that you speak of “restored quickly when RSTP is already in

use?”). This is what happened when you disconnected the primary look; the port that was ALT,

moved to FWD immediately, but the switch also still needs to create a BDU with the TC bit set to

notify the rest of the network that a topology has occurred and all non-edge designated ports will

transition to BLK, LRN, and then FWD to ensure there are no loops in the rest of the network. This

is why if you have a host on a switchport, and you know for a fact that it is only one host, enable

portfast to configure the port as an edgeport so that it does not have to transition to all the STP

states.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 350-001 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written exam dumps will help you to be the Cisco specialist, clear your 350-001 exam and get the final success.

350-001 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mUVBtM1piOS1IMEU/view?usp=sharing

350-001 Cisco exam dumps (100% Pass Guaranteed) from CertBus: http://www.certgod.com/350-001.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection