CertBus 2017 Real Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!
☆ 400-101 CCIE Exam PDF and VCE Dumps : 732QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2017 Real 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
Following 400-101 732QAs are all new published by Cisco Official Exam Center
Do not worry about your CCIE Newest 400-101 study guide exam preparation? Hand over your problems to CertBus in change of the CCIE Latest 400-101 free download CCIE Routing and Switching Written v5.0 certifications! CertBus provides the latest Cisco CCIE Hotest 400-101 vce exam preparation materials with PDF and VCEs. We CertBus guarantees you passing CCIE Aug 29,2017 Hotest 400-101 vce exam for sure.
get your 400-101 certification easily. CertBus expert team is ready to help you. CertBus – help you to pass all 400-101 certification exams! CertBus – the most professional provider of all 400-101 certifications. pass all the 400-101 exam easily. CertBus – help candidates on all 400-101 certification exams preparation. pass 400-101 certification exams, get it certifications easily.
We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html
QUESTION NO:5
Refer to the exhibit.
A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used
for the default route, pointing to both interfaces with a different administrative distance, so that one
of the default routes is preferred.
Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.
After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static
route remained active. They lost their Internet connectivity, even though the backup link was
operating.
Which two possible solutions can be implemented to avoid this situation in the future? (Choose
two.)
A. Implement HSRP link tracking on the branch router R1.
B. Use a track object with an IP SLA probe for the static route on R1.
C. Track the link state of the Ethernet link using a track object on R1.
D. Use a routing protocol between R1 and the upstream ISP.
Answer: B,D
Explanation:
Interface Tracking
Interface tracking allows you to specify another interface on the router for the HSRP process to
monitor in order to alter the HSRP priority for a given group.
If the specified interface’s line protocol goes down, the HSRP priority of this router is reduced,
allowing another HSRP router with higher priority can become active (if it has preemption
enabled).
To configure HSRP interface tracking, use the standby [group] track interface [priority] command.
When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you
explicitly set the decrement value, then the value is decreased by that amount if that interface is
down, and decrements are cumulative. If you do not set an explicit decrement value, then the
value is decreased by 10 for each interface that goes down, and decrements are cumulative.
The following example uses the following configuration, with the default decrement value of 10.
Note: When an HSRP group number is not specified, the default group number is group 0.
interface ethernet0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.3
standby priority 110
standby track serial0
standby track serial1
The HSRP behavior with this configuration is:
0 interfaces down = no decrease (priority is 110)
1 interface down = decrease by 10 (priority becomes100)
2 interfaces down = decrease by 10 (priority becomes 90)
Reference
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i
ntracking
QUESTION NO:10
Which command is used to enable EtherChannel hashing for Layer 3 IP and Layer 4 port-based
CEF?
A. mpls ip cef
B. port-channel ip cef
C. mpls ip port-channel cef
D. port-channel load balance
E. mpls ip load-balance
F. ip cef EtherChannel channel-id XOR L4
G. ip cef connection exchange
Answer: D
Explanation:
QUESTION NO:14
Which three options are features of VTP version 3? (Choose three.)
A. VTPv3 supports 8K VLANs.
B. VTPv3 supports private VLAN mapping.
C. VTPv3 allows for domain discovery.
D. VTPv3 uses a primary server concept to avoid configuration revision issues.
E. VTPv3 is not compatible with VTPv1 or VTPv2.
F. VTPv3 has a hidden password option.
Answer: B,D,F
Explanation:
Key Benefits of VTP Version 3
Much work has gone into improving the usability of VTP version 3 in three major areas:
The new version of VTP offers better administrative control over which device is allowed to update
other devices’ view of the VLAN topology. The chance of unintended and disruptive changes is
significantly reduced, and availability is increased. The reduced risk of unintended changes will
ease the change process and help speed deployment.
Functionality for the VLAN environment has been significantly expanded. Two enhancements are
most beneficial for today’s networks:
QUESTION NO:16
In 802.1s, how is the VLAN to instance mapping represented in the BPDU?
A. The VLAN to instance mapping is a normal 16-byte field in the MST BPDU.
B. The VLAN to instance mapping is a normal 12-byte field in the MST BPDU.
C. The VLAN to instance mapping is a 16-byte MD5 signature field in the MST BPDU.
D. The VLAN to instance mapping is a 12-byte MD5 signature field in the MST BPDU.
Answer: C
Explanation:
MST Configuration and MST Region
Each switch running MST in the network has a single MST configuration that consists of these
three attributes:
1. An alphanumeric configuration name (32 bytes)
2. A configuration revision number (two bytes)
3. A 4096-element table that associates each of the potential 4096 VLANs supported on the
chassis to a given instance.
In order to be part of a common MST region, a group of switches must share the same
configuration attributes.
It is up to the network administrator to properly propagate the configuration throughout the region.
Currently, this step is only possible by the means of the command line interface (CLI) or through
Simple Network
Management Protocol (SNMP). Other methods can be envisioned, as the IEEE specification does
not explicitly mention how to accomplish that step.
Note: If for any reason two switches differ on one or more configuration attribute, the switches are
part of different regions. For more information refer to the Region Boundary section of this
document.
Region Boundary
In order to ensure consistent VLAN-to-instance mapping, it is necessary for the protocol to be able
to exactly identify the boundaries of the regions. For that purpose, the characteristics of the region
are included in the BPDUs. The exact VLANs-to-instance mapping is not propagated in the BPDU,
because the switches only need to know whether they are in the same region as a neighbor.
Therefore, only a digest of the VLANs-toinstance mapping table is sent, along with the revision
number and the name. Once a switch receives a BPDU, the switch extracts the digest (a
numerical value derived from the VLAN-to-instance mapping table through a mathematical
function) and compares this digest with its own computed digest. If the digests differ, the port on
which the BPDU was received is at the boundary of a region.
In generic terms, a port is at the boundary of a region if the designated bridge on its segment is in
a different region or if it receives legacy 802.1d BPDUs. In this diagram, the port on B1 is at the
boundary of region A, whereas the ports on B2 and B3 are internal to region B:
MST Instances
According to the IEEE 802.1s specification, an MST bridge must be able to handle at least these
two instances:
One Internal Spanning Tree (IST)
One or more Multiple Spanning Tree Instance(s) (MSTIs)
The terminology continues to evolve, as 802.1s is actually in a pre-standard phase. It is likely
these names will change in the final release of 802.1s. The Cisco implementation supports 16
instances: one IST (instance 0) and 15 MSTIs.
show vtp status
Cisco switches “show vtp status” Field Descriptions has a MD5 digest field that is a 16-byte
checksum of the
VTP configuration as shown below
Router# show vtp status
VTP Version: 3 (capable)
Configuration Revision: 1
Maximum VLANs supported locally: 1005
Number of existing VLANs: 37
VTP Operating Mode: Server
VTP Domain Name: [smartports]
VTP Pruning Mode: Disabled
VTP V2 Mode: Enabled
VTP Traps Generation: Disabled
MD5 digest : 0x26 0xEE 0x0D 0x84 0x73 0x0E 0x1B 0x69
Configuration last modified by 172.20.52.19 at 7-25-08 14:33:43
Local updater ID is 172.20.52.19 on interface Gi5/2 (first layer3 interface fou)
VTP version running: 2
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfc.shtml
http://www.cisco.com/en/US/docs/ios-xml/ios/lanswitch/command/lsw-cr-book.pdf
QUESTION NO:17
Which three combinations are valid LACP configurations that will set up a channel? (Choose
three.)
A. On/On
B. On/Auto
C. Passive/Active
D. Desirable/Auto
E. Active/Active
F. Desirable/Desirable
Answer: A,C,E
Explanation:
400-101 PDF Dumps400-101 VCE Dumps400-101 Practice Test
QUESTION NO:26
Refer to the exhibit.
Why is AS 65333 in parentheses?
A. It is an external AS.
B. It is a confederation AS.
C. It is the AS of a route reflector.
D. It is our own AS.
E. A route map has been applied to this route.
F. The BGP next hop is unreachable.
Answer: B
Explanation:
QUESTION NO:30
What is the flooding scope of an OSPFv3 LSA, if the value of the S2 bit is set to 1 and the S1 bit is
set to 0?
A. link local
B. area wide
C. AS wide
D. reserved
Answer: C
Explanation:
The Type 1 router LSA is now link local and the Type 2 Network LSA is AS Wide
S2 and S1 indicate the LSA’s flooding scope. Table 9-1 shows the possible values of these two
bits and the associated flooding scopes.
Table 9-1 S bits in the OSPFv3 LSA Link State Type field and their associated flooding scopes
LSA Function Code, the last 13 bits of the LS Type field, corresponds to the OSPFv2 Type field.
Table 9-2 shows the common LSA types used by OSPFv3 and the values of their corresponding
LS Types. If you decode the hex values, you will see that the default U bit of all of them is 0. The S
bits of all LSAs except two indicate area scope. Of the remaining two, AS External LSAs have an
AS flooding scope and Link LSAs have a linklocal flooding scope. Most of the OSPFv3 LSAs have
functional counterparts in OSPFv2; these OSPFv2 LSAs and their types are also shown in Table
9-2.
Table 9-2 OSPFv3 LSA types and their OSPFv2 counterparts
Reference
http://www.networkworld.com/subnets/cisco/050107-ch9-ospfv3.html?page=1
QUESTION NO:33
Which two OSPF LSA types are new in OSPF version 3? (Choose two.)
A. Link
B. NSSA external
C. Network link
D. Intra-area prefix
E. AS domain
Answer: A,D
Explanation:
New LSA Types
OSPFv3 carries over the seven basic LSA types we’re familiar with from OSPFv2. However, the
type 1 and 2 LSAs have been re-purposed, as will be discussed in a bit. OSPFv3 also introduces
two new LSA types: Link and Intra-area Prefix.
Reference
http://packetlife.net/blog/2010/mar/2/ospfv2-versus-ospfv3/
QUESTION NO:34
In order to maintain security, with which hop count are IPv6 neighbor discovery packets sent?
A. 0
B. 1
C. 255
D. 256
Answer: C
Explanation:
QUESTION NO:35
Which command will define a VRF with name ‘CCIE’ in IPv6?
A. ip vrf CCIE
B. ipv6 vrf CCIE
C. vrf definition CCIE
D. ipv6 vrf definition CCIE
Answer: C
Explanation:
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.
400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.