[Newest Version] Free CertBus Cisco 400-101 PDF and Exam Questions Download 100% Pass Exam

CertBus 2017 Valid Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

☆ 400-101 CCIE Exam PDF and VCE Dumps : 828QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2017 Valid 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 828QAs are all new published by Cisco Official Exam Center

Don’t worry about how to get yourself well prepared your CCIE Sep 30,2017 Newest 400-101 QAs exam! CertBus will work you out of your CCIE Newest 400-101 pdf dumps exam with the latest updated Hotest 400-101 exam questions CCIE Routing and Switching Written v5.0 PDF and VCE dumps. CertBus provides the latest real Cisco CCIE Newest 400-101 QAs exam preparation material, covering every aspect of Newest 400-101 vce exam curriculum.

CertBus – professional 400-101 certification exam dumps provider. we do all things to help with your exams. get your 400-101 certification easily. CertBus expert team is ready to help you. CertBus expert team is will help you to get all 400-101 certifications easily. CertBus – 100% real 400-101 certification exam questions and answers. easily pass with a high score.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html

QUESTION NO:1

Which two commands are required to enable multicast on a router, knowing that the receivers only

support IGMPv2? (Choose two.)

A. ip pim rp-address

B. ip pim ssm

C. ip pim sparse-mode

D. ip pim passive

Answer: A,C

Explanation:

Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode

it is supposed that in every network there is someone who is requesting the multicast traffic so

PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from

where a prune message is received to eliminate the

QUESTION NO:2

A branch router is configured with an egress QoS policy that was designed for a total number of

10 concurrent VOIP calls.

Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was

established, all calls were affected and the voice quality was dramatically degraded.

Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS

configuration should be updated due to the new traffic profile?

A. Increase the shaping rate for the priority queue. B.

Remove the policer applied on the priority queue. C.

Remove the shaper applied on the priority queue. D.

Increase the policing rate for the priority queue.

Answer: D

Explanation:

QUESTION NO:5

Refer to the exhibit.

A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used

for the default route, pointing to both interfaces with a different administrative distance, so that one

of the default routes is preferred.

Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.

After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static

route remained active. They lost their Internet connectivity, even though the backup link was

operating.

Which two possible solutions can be implemented to avoid this situation in the future? (Choose

two.)

A. Implement HSRP link tracking on the branch router R1.

B. Use a track object with an IP SLA probe for the static route on R1.

C. Track the link state of the Ethernet link using a track object on R1.

D. Use a routing protocol between R1 and the upstream ISP.

Answer: B,D

Explanation:

Interface Tracking

Interface tracking allows you to specify another interface on the router for the HSRP process to

monitor in order to alter the HSRP priority for a given group.

If the specified interface’s line protocol goes down, the HSRP priority of this router is reduced,

allowing another HSRP router with higher priority can become active (if it has preemption

enabled).

To configure HSRP interface tracking, use the standby [group] track interface [priority] command.

When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you

explicitly set the decrement value, then the value is decreased by that amount if that interface is

down, and decrements are cumulative. If you do not set an explicit decrement value, then the

value is decreased by 10 for each interface that goes down, and decrements are cumulative.

The following example uses the following configuration, with the default decrement value of 10.

Note: When an HSRP group number is not specified, the default group number is group 0.

interface ethernet0

ip address 10.1.1.1 255.255.255.0

standby ip 10.1.1.3

standby priority 110

standby track serial0

standby track serial1

The HSRP behavior with this configuration is:

0 interfaces down = no decrease (priority is 110)

1 interface down = decrease by 10 (priority becomes100)

2 interfaces down = decrease by 10 (priority becomes 90)

Reference

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i

ntracking

QUESTION NO:7

Which statement is true about TCN propagation?

A. The originator of the TCN immediately floods this information through the network.

B. The TCN propagation is a two step process.

C. A TCN is generated and sent to the root bridge.

D. The root bridge must flood this information throughout the network.

Answer: C

Explanation:

Explanation

New Topology Change Mechanisms

When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the

root bridge.

This is shown in this diagram:

Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the

BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge

receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay

seconds. This ensures a relatively quick flush of stale information. Refer to Understanding

Spanning-Tree Protocol Topology Changes for more information on this process. This topology

change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its

propagation through the network evolve.

Topology Change Detection

In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This

means that a loss of connectivity is not considered as a topology change any more, contrary to

802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge

detects a topology change, these occur:

It starts the TC While timer with a value equal to twice the hello-time for all its non-edge

designated ports and its root port, if necessary.

It flushes the MAC addresses associated with all these ports.

Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC

bit set.

BPDUs are also sent on the root port while the timer is active.

Topology Change Propagation

When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:

It clears the MAC addresses learned on all its ports, except the one that receives the topology

change.

It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port

(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).

This way, the TCN floods very quickly across the whole network. The TC propagation is now a one

step process. In fact, the initiator of the topology change floods this information throughout the

network, as opposed to 802.1D where only the root did. This mechanism is much faster than the

802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the

topology change state for the whole network for seconds.

In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of

the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but

on the other hand it clears potential stale information that prevents rapid connectivity restitution.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

QUESTION NO:14

Which three options are features of VTP version 3? (Choose three.)

A. VTPv3 supports 8K VLANs.

B. VTPv3 supports private VLAN mapping.

C. VTPv3 allows for domain discovery.

D. VTPv3 uses a primary server concept to avoid configuration revision issues.

E. VTPv3 is not compatible with VTPv1 or VTPv2.

F. VTPv3 has a hidden password option.

Answer: B,D,F

Explanation:

Key Benefits of VTP Version 3

Much work has gone into improving the usability of VTP version 3 in three major areas:

The new version of VTP offers better administrative control over which device is allowed to update

other devices’ view of the VLAN topology. The chance of unintended and disruptive changes is

significantly reduced, and availability is increased. The reduced risk of unintended changes will

ease the change process and help speed deployment.

Functionality for the VLAN environment has been significantly expanded. Two enhancements are

most beneficial for today’s networks:

Latest 400-101 Dumps400-101 PDF Dumps400-101 Practice Test

QUESTION NO:15

Which three options are considered in the spanning-tree decision process? (Choose three.)

A. lowest root bridge ID

B. lowest path cost to root bridge

C. lowest sender bridge ID

D. highest port ID

E. highest root bridge ID

F. highest path cost to root bridge

Answer: A,B,C

Explanation:

Configuration bridge protocol data units (BPDUs) are sent between switches for each port.

Switches use s four step process to save a copy of the best BPDU seen on every port. When a

port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds

(default), it begins sending them again.

Step 1 Lowest Root Bridge ID (BID)

Step 2 Lowest Path Cost to Root Bridge

Step 3 Lowest Sender BID

Step 4 Lowest Port ID

Reference

Cisco General Networking Theory Quick Reference Sheets

QUESTION NO:24

Refer to the exhibit.

R1 is not learning about the 172.16.10.0 subnet from the BGP neighbor R2 (209.165.202.130).

What can be done so that R1 will learn about this network?

A. Disable auto-summary on R2.

B. Configure an explicit network command for the 172.16.10.0 subnet on R2.

C. Subnet information cannot be passed between IBGP peers.

D. Disable auto-summary on R1.

Answer: B

Explanation:

By default, BGP does not accept subnets redistributed from IGP. To advertise and carry subnet

routes in BGP, use an explicit network command or the no auto-summary command. If you disable

auto-summarization and have not entered a network command, you will not advertise network

routes for networks with subnet routes unless they contain a summary route.

Reference

http://www.cisco.com/en/US/docs/ios/11_3/np1/command/reference/1rbgp.html

QUESTION NO:31

How will EIGRPv6 react if there is an IPv6 subnet mask mismatch between the Global Unicast

addresses on a point-to-point link?

A. EIGRPv6 will form a neighbor relationship.

B. EIGRPv6 will not form a neighbor relationship.

C. EIGRPv6 will form a neighbor relationship, but with the log MSG: “EIGRPv6 neighbor not on a

common subnet.”

D. EIGRPv6 will form a neighbor relationship, but routes learned from that neighbor will not be

installed in the routing table.

Answer: A Explanation:

http://www.ietf.org/rfc/rfc3587.txt

QUESTION NO:35

Which command will define a VRF with name ‘CCIE’ in IPv6?

A. ip vrf CCIE

B. ipv6 vrf CCIE

C. vrf definition CCIE

D. ipv6 vrf definition CCIE

Answer: C

Explanation:

QUESTION NO:36

For which routes does LDP advertise a label binding?

A. all routes in the routing table

B. only the IGP and BGP routes in the routing table

C. only the BGP routes in the routing table

D. only the IGP routes in the routing table

Answer: D

Explanation:

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection